opto22奥普图 SNAP-PAC-R1-FM-产品快照

产品介绍

opto22奥普图 SNAP-PAC-R1-FM

opto22/奥普图 SNAP-PAC-R1-FM

opto22奥普图

SNAP PAC R-series Programmable Automation Controller - On-the-rack - REST API - Analog, full digital, serial; Factory Mutual approved. ; Build your system with the SNAP I/O Configurator . Now developer and IoT ready with a built-in HTTP/HTTPS server and RESTful API. See Programming and Protocols, below. ** Compatible with groov —the easy way to build mobile operator interfaces and securely use them to monitor and control your automation systems and equipment from your smartphone or tablet. ** The SNAP-PAC-R1-FM programmable automation controller provides control, communication, and I/O processing in a compact, rack-mounted package. One of four components of the SNAP PAC System, the SNAP-PAC-R1-FM is fully integrated with PAC Project software, SNAP PAC brains, and SNAP I/O modules. NOTE: The SNAP-PAC-R1-FM is Factory Mutual approved. If you do not need FM approval, see the SNAP-PAC-R1 instead. Used with the included PAC Project Basic software suite (or PAC Project Professional, purchased separately), the Ethernet-based SNAP-PAC-R1-FM can handle almost all your industrial control, remote monitoring, and data acquisition needs. System Architecture This intelligent, flexible PAC can be used in several ways. The SNAP-PAC-R1-FM can provide complete cell control on its own rack with I/O modules. It can also control SNAP PAC I/O units at the same time for a larger system. Or the R1 can be used in a more extensive distributed control system as an I/O unit controlled by a SNAP PAC S-series standalone controller. It can even be used as intelligent remote I/O for Allen-Bradley Logix PLC systems, such as ControlLogix and MicroLogix. Networking Two independent, 10/100 Mbps Ethernet network interfaces are included on each SNAP-PAC-R1. These interfaces have separate IP addresses and can be used to segment the control network from the company network or to provide Ethernet link redundancy in case of link failure or maintenance. In addition, the controller has an RS-232 serial port with hardware handshaking, which can be used for PPP (Point-to-Point Protocol) communication over a modem or for direct connection to serial devices. Programming and Protocols The SNAP-PAC-R1-FM is programmed using the included PAC Control software. PAC Control is a flowchart-based tool for developing control applications, or strategies . You create and debug the strategy on your computer and then download it to the R1, where it runs independently. The controller has 16 MB of RAM and can run up to 16 PAC Control flowcharts at once (many more can be included in the strategy). REST API: All I/O point and strategy variable data is available for secure access using the built-in HTTPS server and RESTful API, with data delivered in JSON format. For complete API documentation and steps for getting started, see developer.opto22.com . In addition, two Node-RED nodes are available. Note that minimum firmware R9.5a and PAC Project R9.5a are required to use the REST API. You can build full-featured operator interfaces (HMIs) using the included PAC Display software, which taps the same tagname database you've already developed in PAC Control. OR take advantage of Opto 22's groov to quickly build and view HMIs you can use on virtually any computer, tablet, or smartphone—any screen size, from any manufacturer—using just a modern web browser (like Firefox or Chrome). Learn more at groov.com . In addition to control, the SNAP-PAC-R1-FM provides communication. Because it is based on the Internet Protocol (IP), the SNAP-PAC-R1-FM can communicate simultaneously using several different protocols, including TCP/IP, PPP, Modbus/TCP, SNMP for network management, SMTP for emailing, and OptoMMP, the open memory-mapped protocol used by all Opto 22 Ethernet-based devices. I/O Processing The controller mounts on a SNAP PAC mounting rack with up to 4 , 8 , 12 , or 16 digital, analog, serial, and special-purpose I/O modules. Choose the modules needed for your application from the extensive line of SNAP I/O modules. Analog features include thermocouple linearization, minimum/maximum values, offset and gain calibration, scaling, ramping, TPO, output clamping, filter weight, and watchdog timer. The SNAP-PAC-R1-FM also offers up to 96 PID loops. Digital features on 4-channel digital modules include latching, high-speed counting (up to 20 kHz depending on the module), quadrature counting, pulse generation and measurement, TPO, and watchdog timer. Features on high-density digital modules are more limited (see module data sheet for details). If you don't need full digital features, see the SNAP-PAC-R2-FM . Compare all SNAP PAC controllers and brains . Build your system in the SNAP I/O Configurator .

Processor 200 MHz 32-bit ColdFire ® 5475 with integrated floating-point unit (FPU) Memory Total RAM Battery-backed RAM Flash Wired+Wireless models 32 MB (10 MB available for PAC Control strategy and 4 MB for file storage. Other models 16 MB (5 MB available for PAC Control strategy and 2 MB for file storage) 2 MB (1 MB available for PAC Control strategy) 8 MB (3.25 MB available for PAC Control strategy; 384 KB available for file storage) Removable storage (Models with manufacture dates of November 2008 and newer. Requires firmware R9.4a or higher and loader R6.1a or higher) MicroSD card slot: supports microSD or microSDHC cards to 32 GB. (Note: Models with card slots and firmware R8.4 through R9.3e support microSD cards up to 2 GB only.) Backup battery Rechargeable (recharges whenever the brain has power), 3-year power-off data retention (replacement part number: SNAP-PAC-BATTERY-ML2430) 1 Communication (wired) Ethernet RS-232 serial Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connectors) Each interface has a separate IP address. Connects to host and I/O. One RS-232 serial port 2 with hardware handshaking. Connects to host (via modem and PPP) or serial device. Cannot connect to serial I/O. Communication (wireless) 3 Topologies Security Frequency 802.11a Frequency 802.11b/g Transmit Power Antenna Connector Roaming Wireless LAN interface with separate IP address. Infrastructure, Ad-Hoc 802.11i: AES - Compatible with WPA2 Personal, TKIP - Compatible with WPA Personal, WEP. Note: TKIP/AES security is not supported in Ad-Hoc mode. 5.180–5.240 GHz, 5.745–5.825 GHz 2.412–2.472 GHz, 2.484 GHz 15 dBm maximum Reverse polarity SMA (RP-SMA or RSMA) Supported within an SSID (Service Set Identifier) only I/O unit compatibility SNAP PAC I/O units: SNAP PAC R-series and EB-series I/O units Power requirements 5.0–5.2 VDC @ 1.5 A Hold-down screw Torque: 8 in-lb (0.9 N-m) Connector screw Torque: 1.7 in-lb (0.19 N-m) Environmental Operating temperature Storage temperature Humidity -20 °C to 60 °C -40 °C to 85 °C 0% to 95% relative humidity, non-condensing Software PAC Project Basic PAC Project Professional REST API Includes programming, HMI software, and configuration software; included with purchase of controller. PAC Project Basic plus OPC 2.0-compliant OPC server, database connectivity,OptoControl strategy and OptoDisplay project importing, and support for Ethernet link redundancy or network segmenting. Use HTTPS to access data (read/write or read-only) from controller tags using your chosen programming language. Data returned in JSON. More information at developer.opto22.com Number of charts that can run simultaneously 16 Agency certifications All models: DFARS All models except -W models: CE, RoHS All models except -FM models: UL (-W models only) U.S., FCC Part 15 Subpart C; Canada, IC RSS-210 (-FM and -B models only) Factory Mutual approved, ATEX Warranty 30 months from date of manufacture Other features • Multiple protocol support including TCP/IP, FTP, EtherNet/IP, Modbus/TCP, SNMP v2.0c, OptoMMP™, and SMTP • Built-in I/O processor handles up to 16 digital 4 , analog, and serial I/O modules   on the same rack • Real-time clock • FTP server/client with file system (in RAM and in removable storage) • Scratch Pad area for peer-to-peer communication • Configurable link redundancy or segmented networking for I/O-controller subnetting (when using PAC Project Professional) 1 Models manufactured before July 1, 2007 have a user-replaceable 3-volt CR2032 Lithium battery (typical service life with power off: 5 years). 2 Connecting to a serial device requires configuration in PAC Manager; PAC Control handles communication. 3 Requires a Wired+Wireless model (SNAP-PAC-R1-W or SNAP-PAC-R2-W). 4 SNAP-PAC-R1s with serial numbers lower than 600,000, and all SNAP-PAC-R1-Bs, are limited to eight 4-channel digital modules per rack; remaining eight can be analog, serial, and high-density digital modules.

Opto 22 Home Products SNAP PAC System Product Selector Controllers PAC Project On-the-rack Ethernet (multiple protocols)